Introduction This machine temperature control of high accuracy, the key parts processing, nitride strength, high hardness, small deformation, the accurate determination of the flow rate provides a good condition.RL - Z1B1 - type of cylinder, piston rod, mold and related components are adopted with special material, the aircraft engine corrosion resistant performance is good, even can be used to test F46 (tetrafluoroethylene hexafluoropropylene polymer) etc. Features This instrument in the cylinder, piston rod, mold and related components are adopted with special material, the aircraft engine corrosion resistant performance is good, even can be used to test F46 (tetrafluoroethylene hexafluoropropylene polymer) etc. Technical parameters 1. The temperature control
Around 100-400 ℃ The accuracy of the quasi is not inferior to plus or minus 0.2 ℃ (125 ℃ ~ 300 ℃)
As prescribed by the international standard ISO1133, GB3682 test temperature: 125, 150, 190, 200, 220, 230, 220, 230, 275, 280 and 275 ℃ Wave motion is not inferior to plus or minus 0.1 ℃ (verification regulation JJG878 provisions of the state, shall not exceed + / - 0.5 ℃)
8 h bleaching move 0.1 ℃ or less (within 4 h verification regulation JJG878 provisions of the state, shall not exceed + / - 0.5 ℃)
Cloth 0.5 ℃ or less (verification regulation JJG878 provisions of the state, shall not be greater than 1 ℃)
Points distinguishes the rate of 0.1 ℃ Random error correction
2. The charging cylinder temperature recovery time after 4 min or less
3. The clock
Range of 0 ~ 9.999 s to 999.9 s ~ 9999 s;
Points distinguishing rate 0.001 0.1 s/s / 1 s
4. The cutting device
4.1 automatic cutting equipment cutting: cutting 0 ~ 999 s regularly
4.2 manual cutting knife cutting
5. Mouth Φ 2.095 + / - 0.005 mm inner diameter
1
6. Cylinder diameter Φ 9.550 + / - 0.020 mm
7. The load:
Fine degree is not inferior to plus or minus 0.5%
Combined load: 325 g, 1200 g, 2160 g, 3800 g, 5000 g, 10000 g, 12500 g, 12500 g (according to ISO1133, GB3682 fully equipped with)
8. The national standard samples (PE) test:
Repeat accuracy of 2% or less (verification regulation JG828 provisions of the state, no more than 8%)
Quasi accuracy of 5% or less (national verification regulation JJG828 regulation, not more than + / - 10%)
9. Determine the range of 0.02 ~ 2000 g / 10 min (auto test)
0.03 ~ 50000 px3/10 min (automatic testing)
* can guarantee in the preheating temperature, molten material without outflow;Manual cutting tests reflect speed because of the human body, to have greater impact on high flow rate value.
10. Power source 220 v AC, 50 hz, 6 a
11. The overall dimensions 1 * b * h = 520 * 520 * 890 mm3
12. 40 kg heavy volume of the host, and Jordan farmar cases of 25 kg
Introduction This machine temperature control of high accuracy, the key parts processing, nitride strength, high hardness, small deformation, the accurate determination of the flow rate provides a good condition.RL - Z1B1 - type of cylinder, piston rod, mold and related components are adopted with special material, the aircraft engine corrosion resistant performance is good, even can be used to test F46 (tetrafluoroethylene hexafluoropropylene polymer) etc.
