FX2000 Fiber Spectrometer Introduction: FX2000 fiber optic spectrometer adopts imported high-quality Richardson blazed grating, which increases the sensitivity by 20% and reduces stray light by 50%. At the same time, it adopts double blaze technology and is equipped with UV-sensitized CCD to expand the effective band to 200~1100nm. And all of this is placed in the 72.5mm focal length / symmetrical / non-crossing C-T optical table of the new generation of design. Finally bring you a good spectrometer. Typical application areas: Ultraviolet flue gas analysis requires high signal-to-noise ratio, ultraviolet sensitivity and optical resolution, which requires a spectrometer with excellent comprehensive performance. Reflection/Transmission Spectroscopy Due to the variety of samples and the complex test conditions, the spectrometer needs to have strong system versatility and adaptability. LED sorting light sources typically have a large radiant intensity range, which requires fiber optic spectrometers with dynamic ranges in excess of 3000:1. Features: 1. Double-blazed grating FX2000 adopts imported high-quality Richardson grating, and in the 200~1100nm full-spectrum model, the double-blazed grating used in high-quality models is used to effectively balance the full-spectrum response; 2. UV-sensitized CCD FX2000 fiber optic spectrometer adopts German technology for UV-sensitization of CCD, the UV conversion efficiency is 20% higher than the traditional one, and the service life is doubled. Using UV differential absorption spectrum, it is very suitable for the detection of nitric oxide and sulfur dioxide; 3. Up to 3000:1 dynamic range The FX2000 fiber optic spectrometer has enjoyed a new generation of electronic engineering design, with up to 3000:1 dynamic range, covering a wide range of intensity. Technical parameter: Detection range: 200~1100nm, depending on the grating Wavelength resolution: optimal 0.11nm, based on 1800-line grating, please refer to "Model Table" for details Optical Resolution: Up to 0.24nm (FWHM), based on 1800-line grating and 10μm slit, see Model Table for details Detector: Sony, 2048 pixels CCD Elimination of higher order diffraction: 3 pre, 4 post filter options to eliminate ghost lines in the spectrum Optical table: 72.5mm focal length, f-number 6, symmetrical non-crossing C-T beam path Integration time: 1ms ~ 60s Dynamic range: 2,000:1, significantly better than similar products Signal-to-noise ratio: 250:1 at saturation Stray light: < 0.1%, measurement wavelength 600nm Corrected Linearity: > 99% Optical interface: SMA905 Data transmission: mini-USB, support USB2.0 communication protocol, 480Mbps transmission speed Expansion function port: 30 pin expansion function port, support sharing BreakOut-Board external function expansion board External trigger: 4 external trigger modes: Normal / Level / Edge / Synchronization Trigger delay: 11.458 ± 0.208μs, mainly used for LIBS excitation Size: 128×90×27mm³ Weight: 0.41kg
Introduction: FX2000 fiber optic spectrometer adopts imported high-quality Richardson blazed grating, which increases the sensitivity by 20% and reduces stray light by 50%. At the same time, it adopts double blaze technology and is equipped with UV-sensitized CCD to expand the effective band to 200~1100nm. And all of this is placed in the 72.5mm focal length / symmetrical / non-crossing C-T optical table of the new generation of design. Finally bring you a good spectrometer. Typical application areas: Ultraviolet flue gas analysis requires high signal-to-noise ratio, ultraviolet sensitivity and optical resolution, which requires a spectrometer with excellent comprehensive performance. Reflection/Transmission Spectroscopy Due to the variety of samples and the complex test conditions, the spectrometer needs to have strong system versatility and adaptability. LED sorting light sources typically have a large radiant intensity range, which requires fiber optic spectrometers with dynamic ranges in excess of 3000:1.
