Introduction: Protective film peel strength tester is a new material testing machine combining electronic technology and mechanical transmission. It has wide and accurate loading speed and testing force range, and has high accuracy and sensitivity for the measurement and control of load, deformation and displacement. High-precision speed control motor can be set to stepless test speed. Each integrated component is connected by plugging. Applications: Protective film peel strength tester can be rubber, plastic, plastic, film, textile, fiber, nano-materials, polymer materials, composite materials, packaging tape, paper, wire and cable, fiber optic cable, safety belts, belts, Leather belts, footwear, adhesive tapes, polymers, spring steels, bearing steels, stainless steels (and other high hardness steels), castings, steel plates, strips, non-ferrous metals, automotive parts, alloys, and other non-metallic and metallic materials Tensile, compression, bending, tearing, 90° peeling, 180° peeling, roller peeling, shearing, adhesion, pullout strength, yield strength, elongation elongation, etc. were tested. And some special product tests. Features: 1. Adopt the microcomputer to control the whole test process and dynamically display the load value, displacement value, variant value, test speed and test curve in real time. 2. The computer is used for data processing and analysis, and the test results can be automatically saved. After the test, the maximum strength, the upper and lower yield strength, the hysteresis loop method, the step-by-step approach, the non-proportional extension strength, the tensile strength, the compressive strength, the elongation at any point, the elongation at any point, and the elastic modulus Volume, elongation, stripping interval process or curve comparison, curve amplification. 3. The test software under the full Chinese Windows platform has strong data maximum value, minimum value, average value, net energy, reentry energy, total energy, bending modulus, break point displacement x% load, break point load X%. Displacement, etc. Data Backup: Test data can be saved on any hard disk partition. After the end of the test, the test curve can be retrieved again, and through the curve traversal to reproduce the test and graphics processing functions, the completed test report and test curve can be printed out instantly. 4. All-digital, three-closed-loop (force, deformation, displacement) control system based on neuron adaptive PID algorithm is used to realize three-closed-loop control of force, deformation, and displacement. Each control loop can automatically switch between each There is no impact smoothness when switching between modes. 5, can test force, deformation, displacement and other rate control and maintenance. 6. Online identification of test control parameters. 7, high precision data acquisition system, high resolution. 8. Except for the power interface, all other interfaces adopt the standard USB interface. The interface layout is neat and reasonable, and the insertion and removal are convenient. 9, load displacement curve, load, time curve, displacement, time curve, stress, strain curve 10. Decimal digits, (two and three) physical units, password protection, etc. can be set 11, the test report language can be converted in Chinese and English. 12. Overload emergency stop device, upper and lower travel limit device, automatic power-off leakage system, and automatic break point shutdown Technical Parameters: Model Name: PT-305 Protective Film Peel Strength Tester Capacity selection: 0～20N, 50N, 100N, 200N, 500N, 1KN, 2KN, 5KN (Customized according to customer requirements) Accuracy level: Level 1 Force unit switching: kgf,gf,N,kN,lbf Stress unit switching: MPa,kPa,kgf/cm2,lbf/in2 Control method: Double-bit type (computer host and microcomputer LCD display can be individually tested) Resolution of power: 1/500000 Load accuracy: Within ±0.01% Travel resolution : 0.001mm Display resolution: 0.001N Display mode: Electronic LCD display and computer display Test stroke: Effective stroke about 1000mm (can be customized) Test width: Ø130mm Test speed: 0.001~500mm/min adjustable Control System : Fully Automatic Computer Control Data Acquisition Software Features : Chinese and English Interface Exchange Shutdown mode : Overload shutdown, emergency stop button, automatic shutdown of specimen damage, upper and lower limit setting automatic shutdown Safety Device: Overload Protection, Limiting Element Protection Device Machine power : AC servo motor Mechanical Systems : Precision Ball Screws Power Supply : AC220V/50HZ 10A Machine size: 50×52×120cm (W×D×H) Machine weight : about 75KG
Introduction: Protective film peel strength tester is a new material testing machine combining electronic technology and mechanical transmission. It has wide and accurate loading speed and testing force range, and has high accuracy and sensitivity for the measurement and control of load, deformation and displacement. High-precision speed control motor can be set to stepless test speed. Each integrated component is connected by plugging. Applications: Protective film peel strength tester can be rubber, plastic, plastic, film, textile, fiber, nano-materials, polymer materials, composite materials, packaging tape, paper, wire and cable, fiber optic cable, safety belts, belts, Leather belts, footwear, adhesive tapes, polymers, spring steels, bearing steels, stainless steels (and other high hardness steels), castings, steel plates, strips, non-ferrous metals, automotive parts, alloys, and other non-metallic and metallic materials Tensile, compression, bending, tearing, 90° peeling, 180° peeling, roller peeling, shearing, adhesion, pullout strength, yield strength, elongation elongation, etc. were tested. And some special product tests.
