Features: 1. Original nozzle (two-fluid nozzle) is highly efficient. 2. Color LCD touch screen parameter display: air inlet temperature / air outlet temperature / peristaltic pump speed / air volume / needle frequency. 3. Full-automatic control: One-button start-up, after setting the spray process parameters, the temperature reaches the predetermined temperature, the peristaltic pump sets itself, the operation flow is displayed on the touch screen, and the running process is clearly displayed. 4. Manual control: If the process parameters need to be adjusted during the experiment, it is convenient to switch to the manual state. The whole process of the experiment shows the color touch screen display. 5. There is a nozzle cleaner (through needle), which will automatically clear when the nozzle is blocked, and the frequency of the needle can be adjusted automatically. 6. Shutdown protection function: Just press the stop button when shutting down, the machine will stop running immediately except the fan to ensure that the equipment will not burn out due to misoperation (forced off the fan). 7. The entire system is made of stainless steel, allowing the drying process to proceed in a non-polluting environment. 8. Imported oil-free air compressor, the diameter of the powder spray is normally distributed, the fluidity is very good, the noise is very low, less than 60db. 9. The atomization structure of the imported two-fluid spray, the whole machine is made of high-quality stainless steel material, and the design is compact, no auxiliary equipment is needed. 10. The design of drying temperature control adopts real-time regulation PID constant temperature control technology to make the temperature control in the whole temperature zone accurate and the heating temperature control precision ±1 °C. 11. In order to keep the sample clean, an air inlet filter is provided. 12. The feed amount can be adjusted by the feed peristaltic pump, and the minimum sample volume can reach 50ml. 13. Dry powder after drying, the particle size is relatively uniform, and more than 95% of the dry powder is in the same particle size range. 14. For the adhesive material, there is a nozzle cleaner (through needle), which will automatically clear when the nozzle is blocked, and the frequency of the needle can be automatically adjusted. 15. The innovative tower wall air hammer device prevents material accumulation and higher material recovery rate. Technical Parameters: Inlet air temperature control: 30 °C ~ 300 °C Outlet temperature control: 30 °C ~ 140 °C Evaporation water volume: 3000ml/h to 5000ml/h Maximum feed amount: up to 5000ml/h (adjustable) Feeding mode: peristaltic pump adjustment Minimum feed amount: 200mL Temperature control accuracy: ±1 °C Average drying time: 1.0 to 1.5S Machine power: 15KW / 380V Dimensions: 2100mm (height) × 1150mm (length) × 1000mm (width)
Features: 1. Original nozzle (two-fluid nozzle) is highly efficient. 2. Color LCD touch screen parameter display: air inlet temperature / air outlet temperature / peristaltic pump speed / air volume / needle frequency. 3. Full-automatic control: One-button start-up, after setting the spray process parameters, the temperature reaches the predetermined temperature, the peristaltic pump sets itself, the operation flow is displayed on the touch screen, and the running process is clearly displayed. 4. Manual control: If the process parameters need to be adjusted during the experiment, it is convenient to switch to the manual state. The whole process of the experiment shows the color touch screen display. 5. There is a nozzle cleaner (through needle), which will automatically clear when the nozzle is blocked, and the frequency of the needle can be adjusted automatically. 6. Shutdown protection function: Just press the stop button when shutting down, the machine will stop running immediately except the fan to ensure that the equipment will not burn out due to misoperation (forced off the fan). 7. The entire system is made of stainless steel, allowing the drying process to proceed in a non-polluting environment. 8. Imported oil-free air compressor, the diameter of the powder spray is normally distributed, the fluidity is very good, the noise is very low, less than 60db. 9. The atomization structure of the imported two-fluid spray, the whole machine is made of high-quality stainless steel material, and the design is compact, no auxiliary equipment is needed. 10. The design of drying temperature control adopts real-time regulation PID constant temperature control technology to make the temperature control in the whole temperature zone accurate and the heating temperature control precision ±1 °C. 11. In order to keep the sample clean, an air inlet filter is provided. 12. The feed amount can be adjusted by the feed peristaltic pump, and the minimum sample volume can reach 50ml. 13. Dry powder after drying, the particle size is relatively uniform, and more than 95% of the dry powder is in the same particle size range. 14. For the adhesive material, there is a nozzle cleaner (through needle), which will automatically clear when the nozzle is blocked, and the frequency of the needle can be automatically adjusted. 15. The innovative tower wall air hammer device prevents material accumulation and higher material recovery rate.
