Introduction: JT-6000Y laboratory small spray dryer and its main application in universities, research institutes and laboratories of food, pharmaceutical and chemical companies to produce micro-particle powder, has broad spectrum applicability to all solutions such as emulsions, suspensions, suitable for heat Drying of sensitive materials such as biological products, biological pesticides, enzyme preparations, etc., because the sprayed material is exposed to high temperatures only when it is sprayed into mist-like particles, it is only heated instantaneously, and these active materials can be maintained after drying. Its active ingredients are not destroyed. Features: 1. The laboratory spray dryer is operated by a large color touch screen, temperature control in ten segments, and memory function. 2. The combination of automatic control and manual control, the entire experiment process color touch screen dynamic display. Fully automatic control: One-touch start, set the spray process parameters, the temperature reaches the predetermined temperature, the peristaltic pump starts automatically, the operation animation is displayed on the touch screen, the operation flow is clearly displayed; just press the stop key when shutting down, the machine automatically shuts down safely. Manual control: If you need to adjust the process parameters in the experiment process, you can easily switch to the manual state. The color touch screen is displayed dynamically during the entire experiment. 3. Two-fluid spray atomization structure, the whole machine is made of high-quality stainless steel precision manufacturing, compact design, no auxiliary equipment, easy to use, long-term as new. 5. Shutdown protection function: just press the stop key when shutting down, the machine will stop running immediately except for the fan to ensure that the device will not cause burnout of the heating part due to misoperation (forcibly turning off the fan). 7. PID constant temperature control technology: The use of real-time control PID constant temperature control technology in the design of the drying temperature control, so that the full temperature zone temperature control accuracy, heating temperature control accuracy of ± 1 °C. 8. In order to maintain the purity of the sample, it is equipped with an air inlet filter. 9. The feeding amount can be adjusted by the feed peristaltic pump, and the small amount of sample can be up to 50ml. Magnetic stirrer optional 10. The dry powder after drying has a relatively uniform particle size, and more than 95% of the dry powder is in the same particle size range. 11. For sticky materials, there is a nozzle cleaner (pin), which will be automatically cleared when the nozzle is blocked. The frequency of the needle can be automatically adjusted; 12. The innovative tower wall purging device has a higher material recovery rate. Technical Parameters: 1. Intake air temperature control: 30°C～400°C 2, the air temperature control: 30 °C ~ 200 °C 3, the amount of evaporation water: 1500mL / H ~ 2000ml / h 4, zui small amount of feed: 50mL 5, drying time: 0.8 ~ 1.0S 6, the whole power: 3.8KW/220V 7, zui large amount of feed: peristaltic pump adjustable zui is 2000ml / h 8, can be upgraded into a two-stage separation and collection system 9, real-time PID temperature control technology, inlet temperature and outlet temperature real-time online display, temperature control accuracy of ± 0.5 °C 10, the machine has a misoperation protection function, when the fan and heater switch using the wrong order, the machine automatically reminds, to prevent newcomers from operating the machine. 11. Low-temperature spray dryer has shutdown protection function: just press the stop button when shutting down, the machine will stop running immediately except the fan to ensure that the equipment will not burn out due to misoperation (forced off the fan). 12, color LCD touch screen parameter display: air inlet temperature / air outlet temperature / peristaltic pump speed / air volume / needle frequency 13. Nozzle diameter: 0.5mm/0.7mm/0.75mm/1.0mm/1.5mm/2.0mm optional, and can be customized according to requirements 14. There is a nozzle cleaner (through needle), which will automatically clear when the nozzle is blocked, and the frequency of the needle can be adjusted automatically. 15. The spray dryer is made of stainless steel and the atomizing structure of the two-fluid spray. The spray, drying and collecting system is made of transparent high-quality borosilicate glass material. 16, built-in imported oilless air compressor, dusting particle diameter was normal distribution, good fluidity, and the noise is very low, less than 60db, in line with national laboratory noise standards; 17, tower wall blowing device, higher material yield 18. It can be directly upgraded into a nitrogen circulation system applied to the drying of organic solvents. 19. Equipment size: 1380mm (height) × 770mm (length) × 590mm (width)
Introduction: JT-6000Y laboratory small spray dryer and its main application in universities, research institutes and laboratories of food, pharmaceutical and chemical companies to produce micro-particle powder, has broad spectrum applicability to all solutions such as emulsions, suspensions, suitable for heat Drying of sensitive materials such as biological products, biological pesticides, enzyme preparations, etc., because the sprayed material is exposed to high temperatures only when it is sprayed into mist-like particles, it is only heated instantaneously, and these active materials can be maintained after drying. Its active ingredients are not destroyed.
