Introduction: GIPP-2000T laboratory spray dryer is mainly used in universities, research institutes and food, biological, beverage, chemical, materials, pharmaceutical and other enterprise laboratories to develop and produce micro-particle powder, which is widely used in all solutions such as emulsions and suspensions. Spectral applicability, suitable for the drying of heat sensitive substances such as biological products, biological pesticides, enzyme preparations, etc., because the materials sprayed are only subjected to high temperature when sprayed into mist-sized particles, so they are only heated instantaneously and can be maintained. These active materials retain their active ingredients intact after drying. Applications: Beverages, spices and pigments, milk and egg products, plant and vegetable extracts, pharmaceutical synthesis, heat sensitive materials, polymers and resins, fragrances, blood products, ceramics and superconductors, biochemicals, dyes, soaps And detergents, food binders, oxides, bone meal and tooth powder. Features: 1. Color LCD touch screen parameter display: air inlet temperature / air outlet temperature / peristaltic pump speed / air volume / pin frequency. 2. Full-automatic control: one-button start-up, after setting the spray process parameters, the temperature reaches the predetermined temperature, the peristaltic pump starts itself, the running animation is displayed on the touch screen, and the running process is clearly displayed; just press the stop button when shutting down, the machine is automatically safe. Shut down. 3. Manual control: If you need to adjust the process parameters during the experiment, you can switch to the manual state conveniently. The color touch screen dynamic display (animation) during the whole experiment process. A nozzle cleaner (through needle) is provided, which is automatically cleared when the nozzle is blocked, and the frequency of the needle can be automatically adjusted. 4. Shutdown protection function: Just press the stop button when shutting down, the machine will stop running immediately except the fan to ensure that the equipment will not burn out due to misoperation (forced off the fan). 5. The spray, drying and collection system is made of transparent high-quality borosilicate heat-resistant glass or stainless steel, so that the drying process can be carried out in a non-polluting environment. 6. Built-in imported oil-free air compressor, the diameter of the powder is normally distributed, the fluidity is very good, the noise is very low, less than 60db. 7. The atomization structure of the two-fluid spray, the whole machine is made of high-quality stainless steel material, and the design is compact, no auxiliary equipment is needed. 8. The design of drying temperature control adopts real-time regulation PID constant temperature control technology to make the temperature control in the whole temperature zone accurate and the heating temperature control precision ±1 °C. 9. In order to keep the sample pure, equipped with an air inlet filter. 10. The feed amount can be adjusted by the feed peristaltic pump, and the minimum sample volume can reach 80ml. 11. The dried powder after drying has a relatively uniform particle size, and more than 95% of the dry powder is in the same particle size range. 12. For the sticky material, there is a nozzle cleaner (through needle), which will automatically clear when the nozzle is blocked, and the frequency of the needle can be automatically adjusted. 13. Innovative tower wall purging device with higher material recovery rate. Technical Parameters: Inlet air temperature control: room temperature ~ 250 ° C (adjustable); air temperature: room temperature ~ 140 ° C (adjustable) Evaporation water volume: 1500mL/H～2000ml/h Maximum feeding amount: the peristaltic pump can be adjusted up to 2000ml/h Minimum feed: 50mL Drying time: 0.8~1.0S Nozzle diameter: 0.5mm/0.7mm/0.75mm/1.0mm/1.5mm/2.0mm optional, and can be customized according to requirements Machine power: 3KW/220V Equipment size: 800 × 600 × 1300 (L × W × H) (mm)
Introduction: GIPP-2000T laboratory spray dryer is mainly used in universities, research institutes and food, biological, beverage, chemical, materials, pharmaceutical and other enterprise laboratories to develop and produce micro-particle powder, which is widely used in all solutions such as emulsions and suspensions. Spectral applicability, suitable for the drying of heat sensitive substances such as biological products, biological pesticides, enzyme preparations, etc., because the materials sprayed are only subjected to high temperature when sprayed into mist-sized particles, so they are only heated instantaneously and can be maintained. These active materials retain their active ingredients intact after drying. Applications: Beverages, spices and pigments, milk and egg products, plant and vegetable extracts, pharmaceutical synthesis, heat sensitive materials, polymers and resins, fragrances, blood products, ceramics and superconductors, biochemicals, dyes, soaps And detergents, food binders, oxides, bone meal and tooth powder.
