BLD-635 disc sampler Introduction: It is suitable for cutting round samples of various wool, cotton, chemical fiber, knitting and other fabrics. 1. Accurately cut the standard sample of 100cm2, and combine the electronic balance to weigh the unit weight (gram weight) of the item. 2, the scope of application: textile, paper, packaging, testing and scientific research industries, for the sampling of round samples of various fabrics, wool, cotton, chemical fiber, knitted paper and non-woven fabrics 3. Note: The blade of this instrument is very sharp. Do not put your hand on the bottom during use to avoid damage. 4. The sample taken by the instrument should be carried out on the cork mat. When the instrument is not in use, wipe it clean and put it in the instrument box to avoid damage to the instrument. 5. After using for a period of time, if the blade is not sharp, it can be exchanged. Fabric electronic balance specifications (g): 100g / 0.01g 200g / 0.01g 300 g / 0.01g 500 g / 0.01g 600g / 0.01g1000g / 0.1g Instructions: 5.1. Lay the fabric to be cut on the rubber mat, place the disc sampler on the fabric, pull out the locking device on the sampler, rotate about 90 degrees, hold the cover with one hand, and hold the corrugated handwheel with one hand. And apply a certain pressure, then rotate the corrugated handwheel clockwise (the angle is greater than 90 degrees) to cut the round sample. 5.2. After the sampler is used, the locking device is rotated to the original position so that the blade cannot be exposed to avoid injury to hands and other items. 6. Structure and adjustment 6.1, the cutter blade has four pieces of double-sided blades, which are evenly distributed in four equal parts, and the blades can be replaced. The specific operation is as follows: loosen the Phillips screws (four screws on each piece), remove the blade pressure plate and Sampling the blade, replacing it with a new one, pressing the blade platen, making sure that the blade edge is tangentially clockwise, and the four blades are in the same plane, then tighten the Phillips screw. 6.2, there are straight lines on the bottom of the instrument for fixing the sample, which is easy to cut and prevent the sample from slipping. 7, note: 7.1, the edge of the instrument blade is sharp, and the hand should not be placed on the bottom to avoid damage. 7.2 The instrument should be cut on the rubber mat. When the instrument is not in use, wipe it clean and put it in the instrument box to avoid damage. Note: Please pull the safety buckle when using, and reset the safety buckle after use. Available in a variety of sizes from 100g, 200g, 300g, 600g, 1000g 1500g** to 0.01g.
Introduction: It is suitable for cutting round samples of various wool, cotton, chemical fiber, knitting and other fabrics. 1. Accurately cut the standard sample of 100cm2, and combine the electronic balance to weigh the unit weight (gram weight) of the item. 2, the scope of application: textile, paper, packaging, testing and scientific research industries, for the sampling of round samples of various fabrics, wool, cotton, chemical fiber, knitted paper and non-woven fabrics 3. Note: The blade of this instrument is very sharp. Do not put your hand on the bottom during use to avoid damage. 4. The sample taken by the instrument should be carried out on the cork mat. When the instrument is not in use, wipe it clean and put it in the instrument box to avoid damage to the instrument. 5. After using for a period of time, if the blade is not sharp, it can be exchanged. Fabric electronic balance specifications (g): 100g / 0.01g 200g / 0.01g 300 g / 0.01g 500 g / 0.01g 600g / 0.01g1000g / 0.1g Instructions: 5.1. Lay the fabric to be cut on the rubber mat, place the disc sampler on the fabric, pull out the locking device on the sampler, rotate about 90 degrees, hold the cover with one hand, and hold the corrugated handwheel with one hand. And apply a certain pressure, then rotate the corrugated handwheel clockwise (the angle is greater than 90 degrees) to cut the round sample. 5.2. After the sampler is used, the locking device is rotated to the original position so that the blade cannot be exposed to avoid injury to hands and other items. 6. Structure and adjustment 6.1, the cutter blade has four pieces of double-sided blades, which are evenly distributed in four equal parts, and the blades can be replaced. The specific operation is as follows: loosen the Phillips screws (four screws on each piece), remove the blade pressure plate and Sampling the blade, replacing it with a new one, pressing the blade platen, making sure that the blade edge is tangentially clockwise, and the four blades are in the same plane, then tighten the Phillips screw. 6.2, there are straight lines on the bottom of the instrument for fixing the sample, which is easy to cut and prevent the sample from slipping. 7, note: 7.1, the edge of the instrument blade is sharp, and the hand should not be placed on the bottom to avoid damage. 7.2 The instrument should be cut on the rubber mat. When the instrument is not in use, wipe it clean and put it in the instrument box to avoid damage. Note: Please pull the safety buckle when using, and reset the safety buckle after use. Available in a variety of sizes from 100g, 200g, 300g, 600g, 1000g 1500g** to 0.01g.
