Product introduction: STRONG series two-color infrared thermometers can be widely used in the metallurgical industry (wire rod, hot rolled sheet, forging) and the casting industry, cement kilns, induction heating, monocrystalline silicon and polycrystalline silicon, etc. Especially suitable for long distance measurement of small targets, materials with variable emissivity and accurate temperature measurement in places with strong attenuation. STRONG series two-color thermometers have a solid appearance, adopt stainless steel movement (core diameter is only 59mm), standard with stainless steel protective sleeve (with the function of blowing and cooling), protection grade IP65, seal parts adopt high-temperature rubber, suitable for various industrial occasions. Even if the detection signal attenuates 95%, it will not have any influence on the temperature measurement results in the environment of water vapor, dust, target size change, partial occlusion, and emission rate change. The design of software and hardware is applicable to the processing of a million times of signals, which can meet the user's requirements on the precision, repeatability and other aspects of the instrument. Product features: Covering 300 ℃ ~ 2500 ℃ temperature range Temperature measuring accuracy can reach 0.5%, repeat accuracy of 2 ℃, the partial products resolution of 0.1 ℃ Response time is adjustable 10ms ~ 99.99s Use adjustable lens to measure distance from 0.35m to infinity The detector is controlled by PID thermostat to eliminate the influence of ambient temperature on the measurement 1: the high brightness green LED light source or visible eyepiece can clearly show the position and size of the target under test It has dual color and monochromatic temperature measurement functions In two-color mode, there is a lens stain detection function Industrial OLED screen is used as display interface, man-machine interface friendly Rich peripheral interfaces: 2 independent analog output, 2 alarm output, 1 level output and 1 RS485 communication interface The anti-interference design of hardware and software improves the stability of the system and can resist the interference of 2500VDC pulse group It has the function of antioxidant measurement Up to 26 thermometers can be cascaded and networked via PC Technical parameters: Model: STRONG-SR-6016 Temperature range (℃) : 600 ~ 1600 Detector: Si/Si (laminated silicon) Working wavelength: wavelength 1: (0.7 ~ 1.08) Wave length 2.0.08 Main applications: hot rolling, wire rod, metal forging, casting, vacuum furnace, induction heating, melting glass, cement kiln, semiconductor Distance coefficient: 60:1 Measuring distance: 0.35m to infinity adjustable Accuracy of measurement: plus or minus 0.5% tm ℃ for the upper limit temperature measurement range (tm) Resolution: 0.1 ℃ Repeatability: plus or minus 2 ℃ Monochrome coefficient: 0.100 ~ 1.000, adjustable step distance: 0.001. Dichromatic coefficient: 0.850 ~ 1.150, adjustable step distance: 0.001. Response time: 10ms ~ 99.99s adjustable Signal processing: peak value, valley value, average value, environmental temperature too high and too low alarm, single color, double color can be switched, power off protection and other functions Output: a variety of analog output of 16bit (4mA ~ 20mA, 0mA ~ 20mA, 0V ~ 5V, 0V ~ 10V optional); Resolution of 0.1 ℃, the current loop output maximum load 600 Ω, allowing voltage output current of 10 ma; Analog output 12 bit 4 ma ~ 20 ma, resolution of 1 ℃, current loop output maximum load 600 Ω; Alarm output: upper and lower alarm, unlimited service life of the optocoupler relay; On resistance of 25 or less Ω, maximum allowable voltage AC42V or DC60V, maximum allowable current 120 ma, 2 ms response time; PNP level output (output current 100mA, with overload protection); RS485 output can realize parameter modification, data recording and query, etc. Display mode: industrial OLED display is adopted Power supply: DC (20 ~ 30) V, with overvoltage, overcurrent and short circuit protection, power consumption: 5W (24V @200ma) with built-in EMI filter, resistant to interference of 2500VDC pulse group. Preheating time: built-in thermostatic heater, temperature measurement after 10min of power supply Aiming mode: built-in visible high-brightness green light or eyepiece aiming Interface: Germany binder sealing plug and 12-core high-temperature shield cable (length: 2.5m) Using the environment: no water-cooled: - 30 ℃ ~ + 55 ℃, purging pressure is 0.1 MPa, traffic is 6 l/min Water-cooled: - 30 ℃ ~ + 120 ℃, cooling water pressure is 0.2 MPa, flow rate of 2 l/min Protection grade: IP65
Product introduction: STRONG series two-color infrared thermometers can be widely used in the metallurgical industry (wire rod, hot rolled sheet, forging) and the casting industry, cement kilns, induction heating, monocrystalline silicon and polycrystalline silicon, etc. Especially suitable for long distance measurement of small targets, materials with variable emissivity and accurate temperature measurement in places with strong attenuation. STRONG series two-color thermometers have a solid appearance, adopt stainless steel movement (core diameter is only 59mm), standard with stainless steel protective sleeve (with the function of blowing and cooling), protection grade IP65, seal parts adopt high-temperature rubber, suitable for various industrial occasions. Even if the detection signal attenuates 95%, it will not have any influence on the temperature measurement results in the environment of water vapor, dust, target size change, partial occlusion, and emission rate change. The design of software and hardware is applicable to the processing of a million times of signals, which can meet the user's requirements on the precision, repeatability and other aspects of the instrument.
