Introduction:
Equipment suitable for instrumentation materials, electricians, electronic products, household appliances, auto parts, chemical coatings, aviation
Product and other related product components are tested for suitability for storage, transport, and use in hot, cold and humid environments. The test equipment is mainly applied to the reliability test of constant, wet heat and heat exchange of industrial products. Environmental simulation tests are conducted on the physical and other relevant characteristics of the product to determine whether the performance of the product can still meet the predetermined requirements for dry product design. , improvement, identification and factory inspection. Features:
1. The equipment consists of a tank, a heating system, a refrigeration system, an air circulation system, and a control system.
2. The cabinet design is perfect, and it is processed by CNC machine tools, and it adopts a non-reverse action handle, which is easy to operate.
3. The door seal is made of refined silicone rubber, so that there is no aging and hardening at high and low temperatures.
4. The liner is made of imported SUS304 stainless steel plate, and the outer shell is A3 plate sprayed, which is more clean and beautiful.
5. Insulation system uses ultra-fine glass fiber or rigid polyurethane foam to fill the heat preservation area to ensure the internal temperature of the box.
6. independent heating and cooling system to make the device more efficient heating, cooling, refrigeration systems for the automatic control system and safety protection coordination.
7. Use multi-wing type strong air circulation to avoid any dead angle and make the temperature distribution in the test area even.
8. The air circulation is designed to return air and wind, and the air pressure and wind speed are all in line with the test standards, and it can make the instant temperature of the door open time faster.
9. The temperature control adopts Taiwan imported intelligent temperature and humidity control device, which has the function of P.I.D automatic calculation and high precision.
Standards compliant:
GB/T5170.5-2008 Test methods for environmental testing equipment for electric and electronic products: Damp heat test
GB2423.3-2006 Environmental testing of electronic products Part 2: Test methods Test C: Constant damp heat test Technical Parameters:
Model: HS-225
Studio size D×W×H(mm): 500×600×750
Outer chamber size D × W × H (mm): 1010 × 1100 × 1940
Temperature range: Type A: 0°C to 100°C Type B: -20°C to 100°C Type C: -40°C to 100°C Type D: -70°C to 100°C
Humidity range: 20% to 98% R.H
Humidity deviation: +2 to 3% R.H
Temperature deviation: ±2°C
Volatility/uniformity: ≤±0.5°C ≤2°C
Heating rate: 1.0～3.0°C/min
Cooling rate: 1～1.5°C/min (average rate)
Box material
Outer box material: high quality A3 steel electrostatic spray / SUS304 stainless steel matte line hairline treatment
Inner box material: imported high quality SUS304 stainless steel plate
Insulation material: ultra-fine glass fiber insulation cotton / rigid polyurethane foam
Door seal: double-layer high and low temperature anti-aging and hardened refined silica gel sealing strip
Cold and heat exchange system
Controller table: Accuracy range: Temperature ± 0.1 °C, Display accuracy: Temperature ± 0.1 °C
Temperature sensor: platinum resistance PT100Ω/MV
Circulatory system: temperature-resistant and low-noise motor, extension shaft, stainless steel multi-leaf centrifugal fan
Water supply system: automatic control by electronic liquid level controller, and residual water can be recovered, with water shortage alarm
Humidification method: external isolation, all stainless steel electric steam humidification
Dehumidification mode: using condensation method evaporator coil dew point temperature laminar flow contact dehumidification method
Heating method: Nichrome heated heater
Refrigeration method: unit cooling method / dual (cascade) refrigeration method (air-cooled)
Condenser/evaporator: domestic famous brand
Introduction:
Equipment suitable for instrumentation materials, electricians, electronic products, household appliances, auto parts, chemical coatings, aviation
Product and other related product components are tested for suitability for storage, transport, and use in hot, cold and humid environments. The test equipment is mainly applied to the reliability test of constant, wet heat and heat exchange of industrial products. Environmental simulation tests are conducted on the physical and other relevant characteristics of the product to determine whether the performance of the product can still meet the predetermined requirements for dry product design. , improvement, identification and factory inspection.
