Introduction: AS-200 Bulk Density Tester This instrument uses the volumetric method to measure the bulk density of powder. The volume meter is composed of a funnel, a baffle box, a bracket, a horizontal vibration-free base, and a measuring cup. A balance is also used in the measurement method. The AS-200 Bulk Density Tester is suitable for the measurement of the bulk density of powder coatings, the bulk density of powder coatings, the bulk density of metal powders, and so on. It is also widely used in bulk density measurement in various fields. When applied to the measurement of the bulk density of metal powders, it is only suitable for powders that cannot flow freely through the funnel with an aperture of 5.0 mm. AS-200 is reasonably priced. AS-200 meets a series of international and domestic standards such as 2020 Chinese Pharmacopoeia, USP United States Pharmacopoeia, EP European Pharmacopoeia, ASTM B329\ISO 3923-1 and so on. At the same time, it meets GB/T 1479.1 Metal Powder Bulk Density Determination Part 1: Funnel Method. At the same time, in order to meet the higher requirements of users for measurement accuracy, the manufacturer Huimeike can provide optional calibration certificates and calculations upon user requirements. software. working principle: The medicine powder is put into the screen in the upper combined funnel, flows into the cloth box naturally or by external force, alternately passes through the four glass plates and the square funnel with an inclination angle of 25 degrees in the cloth box, and finally flows into a cylindrical cup of known volume. In a loose state. Then weigh the mass of the medicine powder in the cylindrical cup. Technical Parameters: 1. Meet the standards: USP United States Pharmacopoeia, EP European Pharmacopoeia, ASTM B329\ISO 3923-1 and a series of international and domestic standards. GB/T 1479.1 Determination of Bulk Density of Metal Powder 2. Result output: bulk density 3. The upper combined funnel-assembled by two conical funnels, separated by a cylinder, and put in a stainless steel screen with a hole diameter of 18 mm (the hole diameter can be customized). 4. Material box—the cross section is square, and there are four glass plates inlaid on the aluminum frame obliquely. The front and back walls of the frame are glass baffles, which are easy to disassemble for cleaning. 5. Square funnel—a 60° square cone, with a lower port diameter of 5×12.5 mm. 6. Cylindrical cup—the volume is 25±05 cm³, and the inner diameter is 30±1 mm. 7. Overflow tray-used to hold excess powder. 8. Bench-used to support the upper combined funnel, cloth box, square funnel, cylindrical cup, and overflow tray, and make them at the height shown in the figure below by axis. Use the three screws (two adjustable and one non-adjustable) of the stand to adjust the level. 9. Balance (optional)-used for weighing powder samples, accurate to 05 grams. 10. Size and weight: W150 x D200 x H420 mm/5kgs
Introduction: AS-200 Bulk Density Tester This instrument uses the volumetric method to measure the bulk density of powder. The volume meter is composed of a funnel, a baffle box, a bracket, a horizontal vibration-free base, and a measuring cup. A balance is also used in the measurement method. The AS-200 Bulk Density Tester is suitable for the measurement of the bulk density of powder coatings, the bulk density of powder coatings, the bulk density of metal powders, and so on. It is also widely used in bulk density measurement in various fields. When applied to the measurement of the bulk density of metal powders, it is only suitable for powders that cannot flow freely through the funnel with an aperture of 5.0 mm. AS-200 is reasonably priced. AS-200 meets a series of international and domestic standards such as 2020 Chinese Pharmacopoeia, USP United States Pharmacopoeia, EP European Pharmacopoeia, ASTM B329\ISO 3923-1 and so on. At the same time, it meets GB/T 1479.1 Metal Powder Bulk Density Determination Part 1: Funnel Method. At the same time, in order to meet the higher requirements of users for measurement accuracy, the manufacturer Huimeike can provide optional calibration certificates and calculations upon user requirements. software.
